Can you tile over fake marble?

Can you install porcelain or ceramic tile over pre-existing cultured marble in your bathroom? Covering the cultured marble walls is not a good idea. “Cultured marble” is an acrylic composite and so it will require an epoxy setting material after the surface has been roughed up with either a grinder or sandpaper.

ANSWER. ANSWER – As long as the existing marble floor is structurally sound and well bonded to its substrate without excessive deflection, you can bond over the marble. The marble surface is likely polished or honed and it might have a sealer on it or contaminates from pass use.

Beside above, can you put tile over existing tile? If your old ceramic tile is worn or dated, you can lay new tile right over the old, and avoid the huge job of tearing out the old tile. This assumes that the floor underneath is solid (concrete) and that there are no cracks in the existing tile (indicating underlying problems in the concrete).

Keeping this in consideration, what adhesive do you use for marble tiles?

Marble tiles should be adhered to the substrate using thin-set or epoxy. Thin-set is a mixture of cement, sand and methylcellulose. Epoxies are also recommended for setting marble tiles. Thin-set and epoxies are not sensitive to water, an important point because marble tile is water sensitive and could absorb moisture.

How do you tile over stone?

Spread a 1/8- to 1/4-inch layer of latex-modified thinset cement over the stone wall, using a cement trowel. Press the thinset cement into the cracks between the stone. Allow the thinset cement to dry for 30 minutes. Repeat the process until the surface is completely smooth.

How much does it cost to retile a fireplace?

The average cost of a custom built fireplace is $3,000 to $5,000, although for more elaborate projects, don’t be surprised if the price creeps towards, or even exceeds, the $10,000 mark. For a custom-built fireplace that uses gas logs, budget an additional $750 to $1,000 for a gas log kit.

Can I paint marble?

There is no doubt that painting over marble can be challenging, but only if you do it the old-fashioned way, with hours of preliminary sanding. With Chalk Paint, you can cover marble in one or two coats with little to no sanding beforehand.

Can I tile over granite?

Instead of removing the existing backsplash we discussed the benefits of tiling over the granite instead. To lay the tile I centered the installation with a plumb line and then burned a flat coat of self-curing thinset into the granite. I then set the tile with the same self-curing thinset.

Can you tile over cultured marble shower floor?

Can you install porcelain or ceramic tile over pre-existing cultured marble in your bathroom? Covering the cultured marble walls is not a good idea. “Cultured marble” is an acrylic composite and so it will require an epoxy setting material after the surface has been roughed up with either a grinder or sandpaper.

How do you remove marble tile from a fireplace?

Place the edge of your cold chisel under the edge of a piece of tile. Tap the hammer gently to move the tip further under the piece and wedge it up. Continue slowly tapping until you pop the piece of tile up. Work your way across the hearth tile by tile.

Can you tile over travertine?

A stone tile floor in good condition can act as the perfect base for new floor coverings. While you should always check with your floor manufacturer to determine the proper subfloor for your application, most ceramic, stone, vinyl, linoleum and floating floors can be installed over a travertine floor.

Should I seal marble tile before installing?

To prevent possible staining and discoloration, we recommend sealing all marble tiles BEFORE installation, and if using grout, AFTER the grouting process. BEFORE applying sealant, wash the tiles and let dry for 24-48 hours. This will ensure that moisture is not present under the surface of the tile.

What type of mortar to use for marble tile?

Modified or latex-modified thinset contains a latex additive. You can also mix this additive into unmodified thinset yourself. The additive makes the mortar more flexible, which is good for the marble tile because it has a little give and won’t “bend” the tile if things shift due to use and weather conditions.

Can you use 1/4 inch cement board on floors?

Floors. Both 1/4- and1/2-inch cement board are appropriate for floors. To install cement board on floors, cement board manufacturers mandate a 5/8-inch plywood subfloor or OSB underlayment. They also require a 3/4-inch subfloor where tile size exceeds 12 inches.

How much space do you need between marble tiles?

Spacing the Tiles The spaces between your tiles should be no more than 1/8-inch wide (a 1/16-inch space is better, if the edges of your tiles are straight enough to accommodate it). Always use plastic spacers to get that consistent line.