That 60 Amp should be a 100 amp correct? It is not violate anything for a main breaker to be of less amperage than the max in the box. If it is used for lights, it will probably be okay.

Most breaker boxes are 100, 150, or **200 amps**. Add the amperages of all the individual breakers in the box. The total may be more than twice the total amperage of the box. For example a 100-amp service panel may have circuit breakers that add up to more than **200 amps**.

Also Know, can you run a 100 amp sub panel off a 100 amp main panel? To the best of my understanding, there is no code issue **running** a 100A **subpanel off** a 100A **main panel**, so long as the wire size is correct, and the installation is correct. For a **subpanel**, **you** need four wire **service** (two hots, a neutral, and an equipment ground).

People also ask, what size breaker do I need for a 100 amp subpanel?

You can use the **100 amp** panel off a 60 **amp breaker** if you determine that it is adequate, but I would suggest that in sizing your feeder wires and conduit it would be a good idea to **size** them to accomodate **100 amps**.

How many watts can a 60 amp breaker handle?

**60**–**amp** 240-volt **circuit**: **60 amps** x 240 volts = 14,400 **watts**.

### How many outlets can be on a 15 amp breaker?

10 outlets

### Can I wire lights and outlets on the same circuit?

An option for you if you don’t want two switches is just to use a blank face plate (check this question). Basic answer to your question of can a mixture of lights and receptacles be installed on a single circuit is yes. The neutral will be white but some switches are wired up with a white wire that is not a neutral.

### How many outlets can be on a 20 amp circuit?

10 receptacles

### Is a double 20 amp breaker 40 amps?

There are two types of standard breakers: single-pole and double-pole. Single-pole breakers are rated for 120 volts and 15 or 20 amps. Double-pole breakers, on the other hand, are typically rated for 20 to 60 amps and supply 240-volt power to large appliances, like electric dryers and ranges.

### What size wire do I need for 100 amp service?

When it comes to the lines connecting master and secondary panels, where the line will carry as much as a full 100 amps, use a 2-gauge non-metallic sheathed electrical cable. The cable must contain one or two hot wires depending on your needs, one neutral wire, and one ground wire. Each wire should be 2-gauge in size.

### How many amps does a normal house draw?

100 amps

### How do I know if I have a 60 or 100 amp service?

Make sure to locate this panel and check what the electrical service is. If there is only 60-amp service, the main breaker will say ’60’ on it. If it’s 100-amp, it’ll simply say ‘100’.

### How many outlets can be on a circuit?

As a rule of thumb in counting devices on a circuit you count each outlet (light or receptacle) as 1.5 amps. Now remember you only count 80% of the rating which means a 15 amp breaker should not exceed 12 amp load, a 20 amp breaker would be 16 amps.

### Does a garage sub panel need a main breaker?

Subpanel main breaker A main breaker on a sub-panel is not necessary because this is in the same building (if you are in a different building then NEC 225.31, 225.32, 225.33 apply). That said, having a main breaker in the sub-panel is also acceptable.

### What size wire do you need for 60 amps?

In practice, however, it’s common to wire 60-amp breakers with 6-gauge, 3-conductor wire because an appliance that needs a 60-amp breaker seldom draws the full 60 amps. If you’re installing a 60-amp subpanel, however, it’s best to connect it to the main panel with 4-gauge wire.

### Can you run a 100 amp subpanel?

Installing a Subpanel and Choosing Cable You must provide from 3 to 4 feet of clearance on all sides of the panel depending on the voltage to ground. If you’re installing a 100-amp panel, you need 4 AWG copper or 2 AWG aluminum three-conductor cable.

### What size breaker do I need for a 125 amp sub panel?

If you have a 125 amp breaker you need 125 amp wire. See the table here. You need to use the 75° column since no one makes a 90° breaker just yet. Since this is a single phase dwelling service you can use #2 AWG copper or 1/0 aluminum for a 125 amp service or main feeder.

### How do you size a subpanel?

Subpanel Coverage Area Measure the length and width of each room and multiply them together to find the square footage of the room. Add up the square footage of all of the rooms to find the total square footage. Multiply the total square footage by 3 (watts) to complete the calculation.

### Can I use aluminum wire for a sub panel?

Aluminum can be used for main service entrance and sub panels. As Firestarter said, fine for sub panels. Aluminum Cons: Larger conductors for the equivalent ampacity as copper.