The NEC doesn’t require GFCI protection for clothes washing machines specifically, but it does for “Laundry Areas.” If the answer is “yes”, then you have your answer- the clothes washing machine will be GFCI protected, because all 120-Volt receptacles are to be GFCI protected in laundry areas, per the 2017 NEC.
Homeowners may mistakenly believe that a washing machine, being a water-using appliance, requires a GFCI outlet. In fact, GFCIs are not required if you only have a washing machine in your laundry room. If, however, there is a sink within six feet of the washing machine outlet, a GFCI outlet is required.
Similarly, should a refrigerator be plugged into a GFCI outlet? In a dwelling unit (residential), GFCI protection is only required for kitchen receptacles that serve the countertop surfaces. There’s no requirement to GFCI protect receptacles that serve a refrigerator. Unless the fridge is plugged into a countertop receptacle.
Secondly, why does my washer keep tripping the GFCI?
To narrow this problem down, there are three places that could be causing the GFCI to trip, a malfunction in the washing machine, a problem with the downstream wiring (aka load side of the GFCI), or the GFCI outlet itself.
Does a washing machine need a dedicated circuit?
120-Volt Laundry Room Service Your laundry room needs a dedicated 20-amp circuit, according to the National Electrical Code, and it can service both the washing machine and a gas dryer. You can have more than one receptacle on this circuit, but all of them must be in the laundry room.
Does a bathroom GFCI need to be on a dedicated circuit?
Bathroom-circuit receptacles. A The main rule of Section 210-11(c)(3) requires a 20A circuit that is dedicated to bathroom receptacle outlets. It does not require a separate circuit for each bathroom. One circuit may supply multiple bathrooms as long as only bathroom receptacles are supplied.
Do all outlets in bathroom need to be GFCI?
The National Electrical Code, or NEC, has specific GFCI requirements for dwelling units. Article 210.8 states that ground-fault circuit-interrupters shall be used for all 125-volt, single-phase, 15- and 20-amp receptacles installed in the following locations: Bathrooms: All receptacles must be GFCI protected.
Can a washing machine share an outlet?
Does the washing machine have to be plugged into a dedicated outlet? Yes. It must be an outlet on a circuit that is dedicated to laundry equipment.
Can you plug a washer into a regular outlet?
Washing machines can be plugged into a standard three-wire grounded AC circuit that is equipped with circuit-breaker protection. The washer should be the only electrical device on the circuit, and the electric outlet should be a grounded three-prong.
How do you ground a washing machine?
The power cord supplied with the washer has a ground wire which is normally found under the main top attached to the galvanized metal trim towards the back. The power cord which should have three prongs is plugged into a polarized and grounded wall outlet.
How many amps does it take to run a washing machine?
Most clothes washers can draw 15 ampsbut thats not the point. Code requires a 20 breaker for the laundry room, a 20 amp breaker means you will need to use 12-2 wire. No, you can not put your dish washer on the same circuit.
What appliances need a dedicated circuit?
Dedicated circuits are required by the National Electrical Code for major electrical appliances such as refrigerators, stoves, washers, dryers, space heaters, and more. Appliances that need a dedicated circuit include: Electric ranges. Wall ovens. Refrigerators. Microwaves. Freezers. Dishwashers. Garbage disposals. Toasters.
Why does my GFCI trip when I plug something in?
If the GFCI detects a ground fault leakage of 5mA it will trip. This leakage is caused by a hot wire touching the ground somewhere on the electrical line such as an appliance or even the outlet itself. This can be caused by water, wires touching, dust or debris, etc.
What would causes washing machine to trip a breaker?
A common cause which may lead to your washer tripping the electrics could be down to a faulty mains filter (also known as the interference suppressor). If your washing machine blows the fuses or trips the RCD as it is connected to the power source then the fault could lie with the mains filter.
Why does my washing machine keep tripping?
The main reasons for tripping of a fuse or RCD when the appliance is the problem is normally an earth leakage or dead short. Most laundry appliances or washing machines will point to the faulty component making the process of correcting the issue straightforward.
What causes a breaker to trip repeatedly?
The circuit breaker trips when too much electricity flows through it or when it cannot handle the excess current load. This means that the flow of electricity is cut off to keep your circuits from overheating or causing more damage.
Does a washing machine need to be arc fault protected?
AFCI Protection: Refer to 210.12(A) of the 2017 NEC, which states: All Dwelling-Unit 120 Volt 15a and 20a branch-circuits supplying outlets or devices in …”laundry areas” shall be AFCI protected. Therefore, by default, the clothes washing machine in a dwelling unit laundry area will be AFCI protected.
Why would an appliance trips the electrics?
In case of an electrical fault, the switch trips, and the circuit is broken. Three of the most common reasons why this may happen are: Too many electrical appliances are in use together, which overloads the circuit. One of the electrical appliances in the house is faulty.
Is there a fuse on a washing machine?
Washing machines have fuses that protect them from power surges. Washing machines require lots of power to run. The other fuse sits in the lid switch on some machines; if the washer overheats or there is a power surge, the washer will not run again until the fuse in the switch is replaced.